A 32 x 16 ft pool that slopes from 3 ft to 8 ft deep holds about 21,065 gallons: 512 sq ft of water surface times a 5.5 ft average depth is 2,816 cu ft, and each cubic foot holds 7.48 gallons.
That is the whole method behind a swimming pool volume calculator: water surface area × average depth = cubic feet, then × 7.48, because a US gallon is 231 cubic inches and a cubic foot is 1,728.
Our pool volume calculator handles rectangle, round, and oval pools, gives gallons, cubic feet, and liters, and adds the fill time if you enter your hose's flow.
How to measure your pool
- Measure the water, not the deck. Take the inside length and width at the water line, wall to wall, in feet. For a round pool, measure the diameter straight across the middle. Convert inches to decimal feet (6 in is 0.5 ft); the square footage calculator guide has a conversion table.
- Measure the water depth at both ends. Lower a tape or a marked pole straight down from the water surface to the floor at the shallow end and at the deep end. If the bottom is flat, enter the same number twice.
- Take more readings if the floor isn't one straight slope. Measure at evenly spaced points along the length, average them, and enter that average as both depths.
- Pick the shape. Rectangle, round, oval (a true ellipse), or oval with straight sides and rounded ends. Kidney and freeform pools have their own section below.
- Optional: measure your hose flow with a bucket and a timer (see the fill time section).
The pool volume formula
- Water surface (sq ft): rectangle = length × width; round = 3.1416 × radius × radius; oval = 3.1416 × half the length × half the width; oval with straight sides = width × (length − width) + 3.1416 × (width ÷ 2) × (width ÷ 2)
- Average depth (ft) = (shallow end + deep end) ÷ 2
- Cubic feet = water surface × average depth
- Gallons = cubic feet × 7.4805; liters = gallons × 3.785
- Fill time (minutes) = gallons ÷ hose flow in gallons per minute (gpm)
NIST Handbook 44 defines the US gallon as 231 cubic inches exactly, so a cubic foot (1,728 cubic inches) holds 1,728 ÷ 231 = 7.4805 gallons; it also lists a gallon as 3.785411784 liters. Pool guides round the factor: the Tulsa Health Department's pool operator manual uses 7.48, and HTH's shock guide uses 7.5, about a quarter of a percent more.
Worked example (the calculator's default values)
A rectangular pool 32 ft long and 16 ft wide, 3 ft deep at the shallow end and 8 ft at the deep end:
- Water surface: 32 × 16 = 512 sq ft
- Average depth: (3 + 8) ÷ 2 = 5.5 ft
- Volume: 512 × 5.5 = 2,816 cu ft
- Gallons: 2,816 × 7.4805 = 21,065 gallons, or about 79,740 liters
The calculator shows: "Your pool holds about 21,065 gallons (2,816 cu ft of water)." and "Water surface: 512 sq ft (rectangle, 32 x 16 ft). Average depth: (3 + 8) / 2 = 5.5 ft. 512 x 5.5 = 2,816 cu ft x 7.4805 gallons per cu ft = 21,065 gallons, or 79,740 liters."
ProPools lists Latham rectangle pool kits from 12 x 24 to 20 x 40 ft, including 16 x 32, with "standard depths ranging from 3' to 8', depending upon pool length," and Pool Warehouse sells a 16 x 32 kit with an 8 ft deep end. The 5.5 ft average assumes an even slope.
Second example: a round pool 24 ft across
The radius is 12 ft, so the water surface is 3.1416 × 12 × 12 = 452.39 sq ft. With 4 ft of water at both ends: "Your pool holds about 13,536 gallons (1,809.56 cu ft of water)." The width field is ignored.
Third example: two kinds of oval
An oval 30 ft long and 15 ft wide with 4 ft of water holds about 10,575 gallons if it is a true ellipse, but about 12,020 gallons if it has straight sides and half-circle ends: 401.71 sq ft of water instead of 353.43, or 13.7% more. Check which shape you have.
Pool gallons by size
Computed with the calculator's math. For an above-ground pool measured in inches, or to top off, multiply the per-inch column by the inches of water. Rectangle sizes follow the Latham kit list on ProPools; round and oval sizes are examples.
| Pool | Water surface (sq ft) | Gallons per inch of depth | At 4 ft deep | At 5.5 ft average |
|---|---|---|---|---|
| Round, 12 ft across | 113.1 | 71 | 3,384 | 4,653 |
| Round, 15 ft across | 176.71 | 110 | 5,288 | 7,271 |
| Round, 18 ft across | 254.47 | 159 | 7,614 | 10,470 |
| Round, 24 ft across | 452.39 | 282 | 13,536 | 18,613 |
| Round, 30 ft across | 706.86 | 441 | 21,151 | 29,082 |
| Oval (ellipse), 15 x 30 ft | 353.43 | 220 | 10,575 | 14,541 |
| Oval with straight sides, 15 x 30 ft | 401.71 | 250 | 12,020 | 16,528 |
| Rectangle, 12 x 24 ft | 288 | 180 | 8,618 | 11,849 |
| Rectangle, 14 x 28 ft | 392 | 244 | 11,729 | 16,128 |
| Rectangle, 16 x 32 ft | 512 | 319 | 15,320 | 21,065 |
| Rectangle, 18 x 36 ft | 648 | 404 | 19,390 | 26,661 |
| Rectangle, 20 x 40 ft | 800 | 499 | 23,938 | 32,914 |
Pool water capacity by size and average depth
An 18 x 36 ft pool holds about 16,966 gallons at a 3.5 ft average depth, 21,813 at 4.5 ft, 24,237 at 5 ft, and 29,084 at 6 ft. Work out your average depth (shallow end plus deep end, divided by 2) and read across; the 4 ft and 5.5 ft columns are in the chart above.
| Rectangle (ft) | At 3.5 ft average | At 4.5 ft average | At 5 ft average | At 6 ft average |
|---|---|---|---|---|
| 12 x 24 | 7,540 | 9,695 | 10,772 | 12,926 |
| 14 x 28 | 10,263 | 13,196 | 14,662 | 17,594 |
| 15 x 30 | 11,782 | 15,148 | 16,831 | 20,197 |
| 16 x 32 | 13,405 | 17,235 | 19,150 | 22,980 |
| 18 x 36 | 16,966 | 21,813 | 24,237 | 29,084 |
| 20 x 40 | 20,945 | 26,930 | 29,922 | 35,906 |
| 22 x 44 | 25,344 | 32,585 | 36,206 | 43,447 |
| 25 x 50 | 32,727 | 42,078 | 46,753 | 56,104 |
Gallons computed with the calculator's math. The sizes are the ones in the City of Akron's pool chart, which multiplies by 7.5 and rounds, so its figures run slightly higher: 24,300 gallons for 18 x 36 ft at 5 ft. To calculate pool gallonage for any other rectangle, multiply length × width × average depth × 7.48, or enter the size in the calculator.
Average backyard pool size and gallons
About 15,000 gallons for an in-ground pool and 7,500 for an above-ground one. A 2010 report for the California Urban Water Conservation Council, based on pool installers' websites and pool industry officials, gives the typical in-ground residential pool as 450 sq ft of water 4.5 ft deep and the typical above-ground pool as 252 sq ft of water 4 ft deep. Many backyard pools are bigger: an APSP fact sheet on pool water use takes 18 x 36 ft as the average in-ground size, and HTH says US residential pools run from 5,000 to over 30,000 gallons.
| Pool | Water surface (sq ft) | Average depth | Gallons | Liters |
|---|---|---|---|---|
| Typical in-ground (California report) | 450, such as 15 x 30 ft | 4.5 ft | 15,148 | 57,342 |
| 16 x 32 ft, 3 to 8 ft deep (the calculator's default) | 512 | 5.5 ft | 21,065 | 79,740 |
| 18 x 36 ft, 3 to 8 ft deep (APSP's average size) | 648 | 5.5 ft | 26,661 | 100,921 |
| Typical above-ground (California report) | 252, about an 18 ft round | 4 ft | 7,540 | 28,543 |
The report lists 15,147 and 7,540 gallons, using 7.48 gallons per cubic foot. Water agencies see similar sizes: the Southern Nevada Water Authority puts the typical residential pool there at around 470 sq ft and backs a 600 sq ft surface area limit on new residential pools, about 15,821 and 20,197 gallons at a 4.5 ft average depth. The 3 to 8 ft depths are the range ProPools gives for Latham rectangle kits. Measure your own pool before you dose chemicals.
Kidney and freeform pools
There is no exact formula for a kidney shape, and two published shortcuts disagree:
- Tulsa Health Department (pool operator manual): (A + B) × L × 0.45 × average depth × 7.48, where A and B are the two widths across the pool and L is the length (Orenda describes A and B as the diameters across the main round areas). Its example, A 16 ft, B 18 ft, L 32 ft and 3 ft deep, comes to 10,987 gallons.
- Orenda (a pool chemical maker): length × the average of A and B. The same pool comes to 12,208 gallons, 11% more.
To run Tulsa's version through the calculator, choose Rectangle and enter 0.45 × (A + B) as the width: 0.45 × 34 = 15.3 ft, with 3 ft at both ends, gives "Your pool holds about 10,987 gallons (1,468.8 cu ft of water)." Treat either number as rough. For a freeform pool, split the water surface into rectangles, as the Tulsa manual does for multi-sided pools, plus circles or half circles for rounded parts; add the areas and multiply by the average depth.
Average depth, slopes, and hoppers
The calculator averages the two depths, the same "Deep End + Shallow End ÷ 2" the Tulsa manual uses. That is exact for a flat floor or an even slope. If the floor stays shallow for a long stretch and then drops into a deep hopper, the true average is lower, so the two-point average overestimates.
Orenda says average depth requires, "at a minimum," the deepest and shallowest readings. For a better number, average readings at evenly spaced points. Say five readings in the default pool are 3, 3.5, 4.5, 6.5, and 8 ft: they average 5.1 ft, and entering 5.1 as both depths gives "Your pool holds about 19,533 gallons (2,611.2 cu ft of water)," about 1,500 gallons less than the two-point estimate.
Above-ground pools
Use the water depth, not the wall height, because the water line sits below the top of the wall. Divide inches by 12 for feet: 48 in is 4 ft. Setting one up? The sand calculator sizes the sand base under the liner; choose Circle for a round pool.
When the maker lists a capacity for your model, use it. Intex lists its 18 ft x 9 ft x 52 in Ultra XTR rectangular frame pool at "4,545 gallon (90%)." If that means water 90 percent of the way up the 52 in wall, the depth is 46.8 in, or 3.9 ft, and the calculator gives 4,726 gallons for 18 x 9 ft, about 4% more. Intex gives 18 x 9 ft as the approximate set-up size, so the water inside can measure a little less.
How long does it take to fill a pool?
Divide the gallons by your hose's flow in gallons per minute. Measure the flow rather than guess. Iowa State University Extension's method: time how long the hose takes to fill a five-gallon bucket, then divide the bucket's capacity by that time in minutes.
If the bucket fills in 30 seconds, the flow is 5 ÷ 0.5 = 10 gpm. Enter 10 as the hose flow for the default pool and the result adds: "At 10 gpm, filling it from empty takes about 35.1 hours (1.5 days)." Measure with the hose and spigot you will actually use.
Why the gallons matter
Pool chemicals are dosed by volume. HTH's shock guide says to "Calculate your total pool volume first, then check the package of shock for dosing recommendations by volume." The CDC's advice for pool owners is to "Read and follow all directions on product labels," so take your gallons to the label; this guide doesn't give doses.
Building around the pool? The CDC recommends "four-sided fencing, which fully encloses the pool and separates it from the house, with self-closing and self-latching gates." The fence calculator counts posts, rails, and pickets for each straight run, and the paver calculator figures pavers, base gravel, and bedding sand for a patio. Check your local code for pool barrier rules.
Pump flow for a 6, 8, or 10 hour turnover
About 59 gpm turns a 21,065 gallon pool over in 6 hours, 44 gpm in 8 hours, and 35 gpm in 10 hours. The Tulsa Health Department's operator manual defines turnover as the time needed to circulate a volume of water equal to the pool's capacity, so the flow is the gallons divided by the minutes: gallons ÷ 360 for 6 hours, ÷ 480 for 8 hours, and ÷ 600 for 10 hours.
| Pool | Gallons | 6 hour turnover (gpm) | 8 hour turnover (gpm) | 10 hour turnover (gpm) |
|---|---|---|---|---|
| Round, 18 ft across, 4 ft deep | 7,614 | 21 | 16 | 13 |
| Round, 24 ft across, 4 ft deep | 13,536 | 38 | 28 | 23 |
| Typical in-ground, 450 sq ft, 4.5 ft deep | 15,148 | 42 | 32 | 25 |
| Rectangle, 16 x 32 ft, 3 to 8 ft | 21,065 | 59 | 44 | 35 |
| Rectangle, 18 x 36 ft, 3 to 8 ft | 26,661 | 74 | 56 | 44 |
| Rectangle, 20 x 40 ft, 3 to 8 ft | 32,914 | 91 | 69 | 55 |
California's Energy Code sets a ceiling for residential pool pumps: the filtration flow "may not be greater than the rate needed to turn over the pool water volume in 6 hours or 36 gpm, whichever is greater," so 36 gpm is the limit for any pool under 12,960 gallons. The Tulsa manual requires an 8 hour turnover for public pools, and Leslie's, a pool supply chain, says most pool owners target an 8 to 10 hour turnover. Run time works the other way: a pump moving 40 gpm turns 20,000 gallons over in about 8.3 hours.
Chemical labels are written by gallons too: HTH's shock products list their dose per 10,000 to 16,750 gallons, depending on the product. Divide your gallons by the label's figure; at 26,661 gallons, an 18 x 36 ft pool takes 2.7 times a per-10,000 gallon amount.
Tips and common mistakes
- Measuring the deck or coping. Use the inside dimensions at the water line.
- Using the wall height of an above-ground pool. The water is lower than the wall.
- Mixing feet and inches. 3 ft 6 in is 3.5 ft, not 3.6.
- Picking the wrong oval. A straight-sided oval holds more than an ellipse of the same length and width.
- Guessing. Orenda warns that pool volume estimates made without measuring are often off by more than 2,000 to 3,000 gallons.
Frequently asked questions
How do I calculate how many gallons are in my pool?
Multiply the water surface in square feet by the average depth in feet, then by 7.48. A 32 x 16 ft pool from 3 to 8 ft deep is 512 × 5.5 = 2,816 cu ft, or about 21,065 gallons.
How much water is in my pool?
Multiply the water surface in square feet by the average depth in feet for cubic feet, then by 7.48 for gallons, or enter your measurements in the calculator above. A 16 x 32 ft in-ground pool that slopes evenly from 3 to 8 ft holds about 21,065 gallons (79,740 liters), and a round above-ground pool 18 ft across with 4 ft of water holds about 7,614 gallons (28,823 liters). The gallons-by-size chart above covers other common sizes.
How many gallons is a 16 x 32 pool?
It depends on the depth. With 4 ft of water throughout it holds about 15,320 gallons; sloping evenly from 3 to 8 ft (a 5.5 ft average), about 21,065 gallons. Each inch of depth is about 319 gallons.
How many gallons is an 18 x 36 pool?
About 26,661 gallons (100,921 liters) if it slopes evenly from 3 to 8 ft, a 5.5 ft average. With 4 ft of water throughout it holds about 19,390 gallons, at a 3.5 to 6 ft average about 16,966 to 29,084 gallons, and each inch of depth is about 404 gallons. ProPools lists 18 x 36 among its Latham rectangle kits, with standard depths from 3 to 8 ft depending on pool length, so measure both ends of yours.
How many gallons is the average backyard pool?
About 15,000 gallons for an in-ground pool and 7,500 for an above-ground one. A 2010 report for the California Urban Water Conservation Council gives the typical in-ground residential pool as 450 sq ft of water 4.5 ft deep, which it lists at 15,147 gallons, and the typical above-ground pool as 252 sq ft 4 ft deep, or 7,540 gallons. Many are bigger: an 18 x 36 ft pool sloping from 3 to 8 ft holds about 26,661 gallons, and HTH says US residential pools run from 5,000 to over 30,000 gallons.
How do I find the volume of a round pool?
Multiply 3.1416 by the radius squared for the water surface, then by the depth and 7.48. A pool 24 ft across with 4 ft of water holds about 13,536 gallons.
How many gallons is an above-ground pool?
It depends on the diameter and the water depth, not the wall height. With 4 ft of water, a round pool 15 ft across holds about 5,288 gallons, 18 ft about 7,614, and 24 ft about 13,536; each inch less takes off about 110, 159, or 282 gallons. Intex lists its 18 ft x 52 in round frame pool at 6,981 gallons, which works out to about 44 in of water across the full 18 ft. If your pool lists a capacity, use it.
How many gallons are in a cubic foot of water?
About 7.48 (7.4805), because NIST defines the US gallon as 231 cubic inches and a cubic foot is 1,728 cubic inches. That is about 28.3 liters.
How many liters is my pool?
About 3.785 liters for every gallon, so multiply the gallons by 3.785, and divide the liters by 1,000 for cubic meters. The 21,065 gallon default pool holds about 79,740 liters, or 79.7 cubic meters, and an 18 x 36 ft pool sloping from 3 to 8 ft about 100,921 liters (100.9 cubic meters). The calculator adds the liters to every result. NIST Handbook 44 lists the US gallon as 3.785411784 liters.
How long does it take to fill a pool with a garden hose?
Gallons ÷ hose flow in gpm gives minutes. Time a five-gallon bucket to find the flow. At 10 gpm, a 21,065 gallon pool takes about 35.1 hours.
What GPM should my pool pump be?
44 to 59 gpm for a 21,065 gallon pool: the gallons divided by 480 turn the water over in 8 hours, and divided by 360, in 6 hours. An 18 x 36 ft pool at 26,661 gallons takes 56 to 74 gpm for the same turnovers. California's Energy Code caps residential pool pumps at the 6 hour rate or 36 gpm, whichever is greater, and the Tulsa Health Department requires an 8 hour turnover for public pools. Leslie's says most pool owners target 8 to 10 hours.
Sources
- NIST Handbook 44 (2026), Appendix C: General Tables of Units of Measurement (PDF)
- Tulsa Health Department: Pool Operators Permit Instruction Manual (PDF)
- Orenda: How to Calculate Swimming Pool Volume
- Intex: Rectangular Ultra XTR Frame 18 ft x 9 ft x 52 in pool
- ProPools: Latham Rectangle Inground Pool Kits
- Pool Warehouse: 16' x 32' Rectangle Pool Kit
- Iowa State University Extension and Outreach: How do I determine how much water to use when watering my garden plants?
- HTH: How much shock do I add to my swimming pool?
- CDC: Guidelines for Keeping Your Pool Safe and Healthy
- Intex: Ultra XTR Frame 18 ft x 52 in Round Above Ground Pool
- City of Akron: How to calculate the gallons in a swimming pool (PDF)
- California Urban Water Conservation Council: Evaluation of Potential Best Management Practices: Pools, Spas, and Fountains (2010, PDF)
- APSP: Facts About Pool Water Usage (PDF, hosted by the Pool & Hot Tub Alliance)
- Southern Nevada Water Authority: Pools and spas
- California Energy Commission: Pool and Spa Heating Systems, Certificate of Installation CF2R-PLB-03-E (PDF)
- Leslie's: How to Calculate Pool Pump Run Time
Spot an error? Tell us.