A 12 x 10 ft paver patio needs 10 cu ft of bedding sand at 1 inch deep: 0.37 cubic yards, about 963 to 1,074 lb of dry sand, or 20 bags of 50 lb.
To figure out how much sand you need, multiply the length by the width in feet, multiply by the depth in inches, and divide by 12 to get cubic feet. Divide by 27 for cubic yards, then multiply by the weight of a cubic yard of sand to get pounds or tons.
Our sand calculator does that for a rectangle or a circle, gives the weight of dry or wet sand as a range, and counts 50 lb bags.
How to measure for sand
- Measure the area in feet. For an L shape, split it into rectangles and add them; the square footage calculator adds up to three. Convert inches to decimal feet (6 in is 0.5 ft).
- For a round area, measure the diameter. Measure straight across through the center, choose Circle, and enter the diameter as the length. The width is not used.
- Pick the depth in inches. Use the depth table below. For a layer that settles, such as sand under a play set, enter the starting depth.
- Choose dry or wet. Wet sand weighs more per cubic yard, which matters when you buy by the ton.
- Add extra if you need it, for uneven ground or a pool's sand cove. Leave it at 0 for the exact volume.
The sand formula
- Area (sq ft): rectangle = length × width; circle = 3.1416 × radius × radius (the radius is half the diameter)
- Cubic feet = area × depth (in) ÷ 12, plus any extra percentage
- Cubic yards = cubic feet ÷ 27
- Weight (lb) = cubic yards × 2,600 to 2,900 for dry sand, or × 2,800 to 3,100 for wet sand; tons = pounds ÷ 2,000
- 50 lb bags = cubic feet ÷ 0.5, rounded up
NIST Handbook 44 gives 27 cubic feet to the cubic yard and 2,000 pounds to the (short) ton. The weights are from the US Army's earthmoving field manual, FM 5-434, which lists dry sand at 2,600 to 2,900 lb and wet sand at 2,800 to 3,100 lb per loose cubic yard and notes that weight varies with grain size, moisture, and compaction. That is why the calculator shows a range instead of one number. For the volume of any other material, the cubic yard calculator does the same math for rectangles, circles, and triangles.
Worked example (the calculator's default values)
A 12 x 10 ft patio with a 1 inch layer of dry bedding sand and no extra:
- Area: 12 × 10 = 120 sq ft
- Volume: 120 × 1 ÷ 12 = 10 cu ft
- Cubic yards: 10 ÷ 27 = 0.37
- Weight: 0.37037 × 2,600 = 963 lb to 0.37037 × 2,900 = 1,074 lb (0.48 to 0.54 tons)
- Bags: 10 ÷ 0.5 = 20 bags of 50 lb
The calculator shows: "You need 0.37 cubic yards of sand (10 cu ft): about 963 to 1,074 lb, or 20 bags of 50 lb." That is the same 10 cu ft of bedding sand the paver calculator gives for this patio, and twenty 50 lb bags weigh 1,000 lb, inside the dry range.
Second example: the sand base for a 24 ft round pool
Choose Circle and enter 24 ft and 2 in. The area is 3.1416 × 12 × 12 = 452.39 sq ft, and 452.39 × 2 ÷ 12 = 75.4 cu ft: "You need 2.79 cubic yards of sand (75.4 cu ft): about 3.63 to 4.05 tons, or 151 bags of 50 lb."
Third example: sand under a home play set
A climber with a 6 x 6 ft footprint, up to 5 ft high (an example size), needs surfacing 6 ft out on every side, so the area is 18 x 18 ft. At a 12 inch starting depth: "You need 12 cubic yards of sand (324 cu ft): about 15.6 to 17.4 tons, or 648 bags of 50 lb." A job this size is a bulk order.
How much sand per 100 square feet
| Depth | Cubic feet | Cubic yards | 50 lb bags | Dry sand (tons) | Wet sand (tons) | 1 cubic yard covers |
|---|---|---|---|---|---|---|
| 1 in | 8.33 | 0.31 | 17 | 0.4 to 0.45 | 0.43 to 0.48 | 324 sq ft |
| 2 in | 16.67 | 0.62 | 34 | 0.8 to 0.9 | 0.86 to 0.96 | 162 sq ft |
| 3 in | 25 | 0.93 | 50 | 1.2 to 1.34 | 1.3 to 1.44 | 108 sq ft |
| 4 in | 33.33 | 1.23 | 67 | 1.6 to 1.79 | 1.73 to 1.91 | 81 sq ft |
| 6 in | 50 | 1.85 | 100 | 2.41 to 2.69 | 2.59 to 2.87 | 54 sq ft |
| 9 in | 75 | 2.78 | 150 | 3.61 to 4.03 | 3.89 to 4.31 | 36 sq ft |
| 12 in | 100 | 3.7 | 200 | 4.81 to 5.37 | 5.19 to 5.74 | 27 sq ft |
For 200 sq ft, double the figures; for 50 sq ft, halve them. The bag column is rounded up to whole bags.
How much does a yard of sand weigh?
| Sand | Pounds per cubic yard | Tons per cubic yard | Source |
|---|---|---|---|
| Dry, loose | 2,600 to 2,900 | 1.3 to 1.45 | FM 5-434 |
| Wet, loose | 2,800 to 3,100 | 1.4 to 1.55 | FM 5-434 |
| Bagged, 50 lb per 0.5 cu ft | 2,700 (54 bags) | 1.35 | QUIKRETE bag yield |
"Loose" means sand in a pile or a truck bed; the manual lists 10 to 15 percent swell for sand dug from the ground. A ton of dry sand is about 18.6 to 20.8 cu ft, enough for 223 to 249 sq ft at 1 inch deep.
QUIKRETE's mason sand data sheet says each 50 lb bag contains approximately 0.5 cu ft, and Lowe's lists QUIKRETE and Sakrete 50 lb play sand at 0.5 cu ft. That is 100 lb per cubic foot, inside the dry range. Sakrete's 50 lb Damp Mason Sand is listed at 0.6 cu ft, so check the yield on your bag.
Tons of sand to cubic yards
A ton of sand is about 0.7 cubic yard. Divide 2,000 lb by the weight of a cubic yard: FM 5-434's 2,600 to 2,900 lb for dry, loose sand gives 0.69 to 0.77 cubic yard per ton, and its 2,800 to 3,100 lb for wet sand gives 0.65 to 0.71. Bagged sand at 50 lb per 0.5 cu ft (100 lb per cubic foot) works out to 0.74 cubic yard, or 40 bags of 50 lb, per ton.
| Tons | Dry sand (cubic yards) | Wet sand (cubic yards) | Bagged sand (cubic yards) |
|---|---|---|---|
| 1 | 0.69 to 0.77 | 0.65 to 0.71 | 0.74 (40 bags) |
| 2 | 1.38 to 1.54 | 1.29 to 1.43 | 1.48 (80 bags) |
| 3 | 2.07 to 2.31 | 1.94 to 2.14 | 2.22 (120 bags) |
| 5 | 3.45 to 3.85 | 3.23 to 3.57 | 3.7 (200 bags) |
| 10 | 6.9 to 7.69 | 6.45 to 7.14 | 7.41 (400 bags) |
| 15 | 10.34 to 11.54 | 9.68 to 10.71 | 11.11 (600 bags) |
| 20 | 13.79 to 15.38 | 12.9 to 14.29 | 14.81 (800 bags) |
To go the other way, multiply cubic yards by 1.3 to 1.45 tons for dry sand or 1.4 to 1.55 for wet; the calculator does it for you and lists the weight in pounds and tons. Wet sand weighs more per cubic yard, so a ton of it fills less space. If a supplier sells by the ton, ask what their sand weighs per cubic yard.
How deep should the sand be?
| Use | Depth to enter | Source |
|---|---|---|
| Paver bedding sand | 1 in (nominal), screeded | CMHA guide specification |
| Base under an above-ground pool | 2 in, plus a 6 to 8 in cove along the wall | Pool owner's manual (Reprieve) |
| Home play set, equipment up to 5 ft high | 12 in to start; it compresses to about 9 in | CPSC Outdoor Home Playground Safety Handbook |
| Sandbox | About 4 to 6 in in a box 8 in deep, leaving a few inches at the top | KidKraft (sandbox maker) |
| Riding arena footing | About 2 in to start, adding 1/2 in at a time; no deeper than 6 in | Penn State Extension |
Pools. One above-ground pool manual calls for a 2 inch base of fine sand without pebbles over the whole pool area, then a 6 to 8 inch cove inside the wall. Royal Swimming Pools also cites a 2 inch base. Its chart, which it calls general estimates, lists 3 cubic yards for a 24 ft round pool with a sand cove; the base alone is 2.79, so add extra for a sand cove. Follow your own pool's manual, and once it is up, the pool volume calculator gives the gallons to fill it.
Play areas. The CPSC's home playground handbook lists 9 inches of sand or pea gravel for equipment up to 5 ft high, notes that a 12 inch initial fill compresses to about 9 inches, and extends the surfacing at least 6 ft from the equipment in all directions (for swings, twice the height of the top bar in front and behind).
Play sand for a sandbox, by sandbox size
Play sand comes in 50 lb bags of about 0.5 cu ft, so a sandbox takes 2 bags for every cubic foot. Multiply the length by the width in feet and by the fill depth in inches, then divide by 12 for cubic feet. Sandbox maker KidKraft suggests 4 to 6 inches of sand in a box 8 inches deep, leaving a few inches of space at the top.
| Sandbox | 4 in deep | 6 in deep | 9 in deep |
|---|---|---|---|
| 4 x 4 ft | 11 bags (5.33 cu ft) | 16 bags (8 cu ft) | 24 bags (12 cu ft) |
| 5 x 5 ft | 17 bags (8.33 cu ft) | 25 bags (12.5 cu ft) | 38 bags (18.75 cu ft) |
| 6 x 6 ft | 24 bags (12 cu ft) | 36 bags (18 cu ft) | 54 bags (27 cu ft) |
| 8 x 8 ft | 43 bags (21.33 cu ft) | 64 bags (32 cu ft) | 96 bags (48 cu ft) |
| Round, 6 ft across | 19 bags (9.42 cu ft) | 29 bags (14.14 cu ft) | 43 bags (21.21 cu ft) |
A 5 x 5 ft box filled 6 inches deep holds 12.5 cu ft: 25 bags, or 1,250 lb of bagged sand. The calculator gives the same 25 bags (choose Rectangle and enter 5, 5, and 6); for a round box, choose Circle and enter the diameter. A 6 x 6 ft box at 9 inches takes a full cubic yard, or 54 bags.
Arena sand for a riding arena, by arena size
Start with about 2 inches of sand and add 1/2 inch at a time as needed, says Penn State Extension, or only 1 1/2 inches for an arena used mostly for driving horses; sand deeper than 6 inches is stressful to horse tendons. University of Kentucky Extension says the riding surface is often 2 to 6 inches thick, depending on use, over a compacted base usually 6 to 8 inches thick. Penn State recommends cleaned and screened, medium to coarse, hard, sharp sand.
| Arena | Area | Sand at 2 in | Sand at 3 in |
|---|---|---|---|
| Every 1,000 sq ft | 1,000 sq ft | 6.2 cu yd (8 to 9 tons) | 9.3 cu yd (12 to 13.4 tons) |
| Riding arena, 60 x 120 ft | 7,200 sq ft | 44.4 cu yd (57.8 to 64.4 tons) | 66.7 cu yd (86.7 to 96.7 tons) |
| Small dressage arena, 66 x 132 ft | 8,712 sq ft | 53.8 cu yd (69.9 to 78 tons) | 80.7 cu yd (104.9 to 117 tons) |
| Standard dressage arena, 66 x 198 ft | 13,068 sq ft | 80.7 cu yd (104.9 to 117 tons) | 121 cu yd (157.3 to 175.5 tons) |
| Show arena, 120 x 240 ft | 28,800 sq ft | 177.8 cu yd (231.1 to 257.8 tons) | 266.7 cu yd (346.7 to 386.7 tons) |
| Round pen, 60 ft across | 2,827 sq ft | 17.5 cu yd (22.7 to 25.3 tons) | 26.2 cu yd (34 to 38 tons) |
Tons are for dry, loose sand at FM 5-434's 2,600 to 2,900 lb per cubic yard. Penn State's footing recipe, which figures sand at 100 lb per cubic foot, calls for 8 tons per 1,000 sq ft at 2 inches and 12 tons at 3 inches, close to the low end of that range. The arena sizes are University of Kentucky Extension's suggested dimensions: 60 x 120 ft sits inside its 50 to 60 by 100 to 130 ft range for riding, the dressage sizes are United States Dressage Federation regulation sizes, and 120 x 240 ft is the US Equestrian (USEF) suggested show size. The round pen is an example size; for it, choose Circle in the calculator and enter the diameter.
Sand for pavers
The Concrete Masonry and Hardscapes Association (CMHA) guide specification spreads washed bedding sand over the base and screeds it to a nominal 1 inch, which is 1 cu ft of sand for every 12 sq ft of patio. Its gradation follows ASTM C33 with a few modifications. The specification also says not to use the bedding sand to fill dips in the base, so fix low spots in the gravel base instead of adding sand.
Joint sand is a second, smaller purchase. CMHA's joint sand follows ASTM C144 grading (coarser C33 sand is also allowed), and it is swept in dry and compacted, with at least 4 passes of the plate compactor, until the joints are full. To size the whole job, the paver calculator counts pavers, base gravel, and bedding sand in one step.
Bedding and joint sand for pavers, by patio size
At the nominal 1 inch bedding depth, every 12 sq ft of patio takes 1 cu ft of sand, or 2 bags of 50 lb. Joint sand is counted by area: QUIKRETE rates a 50 lb bag of its polymeric jointing sand at 85 to 95 sq ft of regular pavers or 50 to 55 sq ft of tumbled pavers, depending on joint width.
| Patio | Bedding sand at 1 in | Bedding sand, 50 lb bags | Joint sand, 50 lb bags (regular pavers) | Joint sand, 50 lb bags (tumbled pavers) |
|---|---|---|---|---|
| 10 x 10 ft (100 sq ft) | 8.33 cu ft (0.31 cu yd) | 17 | 2 | 2 |
| 12 x 12 ft (144 sq ft) | 12 cu ft (0.44 cu yd) | 24 | 2 | 3 |
| 12 x 16 ft (192 sq ft) | 16 cu ft (0.59 cu yd) | 32 | 3 | 4 |
| 16 x 20 ft (320 sq ft) | 26.67 cu ft (0.99 cu yd) | 54 | 4 | 6 to 7 |
| 20 x 20 ft (400 sq ft) | 33.33 cu ft (1.23 cu yd) | 67 | 5 | 8 |
| 20 x 30 ft (600 sq ft) | 50 cu ft (1.85 cu yd) | 100 | 7 to 8 | 11 to 12 |
Buy washed concrete sand (ASTM C33) for the bedding layer: the CMHA specification says not to use mason sand or ASTM C144 sand there. It calls for joints 1/16 to 3/16 inch wide; wider joints take more joint sand, so round up. The bedding bags assume 0.5 cu ft per 50 lb bag, as the calculator does, so check the yield on the bag. From about a cubic yard (the 16 x 20 ft patio), bulk sand by the yard or ton is an option.
Which sand to buy
| Sand | Used for | What the maker or spec says |
|---|---|---|
| Play sand | Sandboxes | Washed and screened (QUIKRETE, Sakrete) |
| All-purpose sand | Concrete; under brick pavers | Meets ASTM C33 (QUIKRETE) |
| Mason sand | Mortar; paver and brick joints | Meets ASTM C144 (QUIKRETE) |
| Paver bedding sand | The 1 in layer under pavers | Washed, ASTM C33 grading (CMHA) |
| Pool base sand | Under a pool liner | Masonry sand (Royal Swimming Pools); fine sand without pebbles (pool manual) |
| Arena sand | Riding arena footing | Cleaned and screened, medium to coarse, hard, sharp sand (Penn State Extension) |
Tips and common mistakes
- Mixing inches and feet. The depth field is in inches. Entering 0.08 for a 1 inch layer gives a result twelve times too small.
- Leveling the base with sand. Bedding sand should be an even 1 inch; CMHA says not to use it to fill depressions in the base.
- Forgetting that loose fill settles. For a play area, start at 12 inches so it ends near 9, and top it up as it compresses.
- Using dry weights for a wet load. Wet sand weighs more, so the same number of tons buys less sand. When you order by the ton and the sand is wet, choose Wet.
Frequently asked questions
How do I calculate how much sand I need?
10 cu ft (0.37 cubic yards) for a 12 x 10 ft area 1 inch deep. To find the volume of sand, multiply length by width in feet and by depth in inches, then divide by 12 for cubic feet and by 27 for cubic yards. For tons, multiply the cubic yards by 1.3 to 1.45 for dry sand (1.4 to 1.55 for wet).
How much sand do I need?
It depends on the area and the depth: every 100 sq ft takes 8.33 cu ft (0.31 cubic yards) for each inch of depth, or 17 bags of 50 lb at 1 inch. The 1 inch bedding layer under a 12 x 10 ft paver patio is 10 cu ft; a 2 inch base under an 18 ft round pool is 1.57 cubic yards before the cove; and the CPSC's 12 inch initial fill for a home play set is 3.7 cubic yards for every 100 sq ft.
How much does a yard of sand weigh?
2,600 to 2,900 lb (1.3 to 1.45 tons) for dry, loose sand and 2,800 to 3,100 lb (1.4 to 1.55 tons) for wet sand, according to the US Army's FM 5-434. That is about 96 to 107 lb per cubic foot dry. Bagged sand at 50 lb per 0.5 cu ft is 100 lb per cubic foot, or 2,700 lb per cubic yard. Weights vary with grain size and moisture, so ask your supplier for the sand they sell.
How many yards are in a ton of sand?
About 0.7 cubic yard. Using the US Army's FM 5-434 weights, a ton of dry, loose sand is 0.69 to 0.77 cubic yard (about 18.6 to 20.8 cu ft), and a ton of wet sand is 0.65 to 0.71 cubic yard. Bagged sand at 100 lb per cubic foot is 0.74 cubic yard, or 40 bags of 50 lb, per ton. So 10 tons of dry sand is about 6.9 to 7.7 cubic yards.
How many tons of sand do I need?
1.3 to 1.45 tons for every cubic yard of dry sand, or 1.4 to 1.55 tons wet, so work out the cubic yards first. 100 sq ft at 2 inches is 0.62 cubic yards, or 0.8 to 0.9 tons of dry sand; the 2 inch base under a 24 ft round pool is 3.63 to 4.05 tons. The calculator gives the cubic yards and the weight in one step.
How many square feet does a ton of sand cover?
About 223 to 249 sq ft at 1 inch deep, for dry, loose sand at the US Army's FM 5-434 weights (18.6 to 20.8 cu ft per ton). At 2 inches that is about 112 to 125 sq ft, and at 4 inches about 56 to 62 sq ft. For any depth, multiply the cubic feet per ton by 12 and divide by the depth in inches.
How many 50 lb bags of sand are in a cubic yard?
About 54. QUIKRETE puts approximately 0.5 cu ft of sand in a 50 lb bag of mason sand, and a cubic yard is 27 cu ft, so 27 ÷ 0.5 = 54 bags. Check the yield printed on the bag you buy.
How much sand do I need for pavers?
About 1 cu ft of bedding sand for every 12 sq ft, at the nominal 1 inch depth: a 12 x 12 ft patio needs 12 cu ft (0.44 cubic yards), or 24 bags of 50 lb. Joint sand is a separate, smaller purchase: QUIKRETE rates a 50 lb bag of its polymeric jointing sand at 85 to 95 sq ft of regular pavers, so the same patio takes 2 bags (3 with tumbled pavers, at 50 to 55 sq ft a bag).
How much sand do I need for an above-ground pool?
A 2 inch base under an 18 ft round pool is 42.41 cu ft (1.57 cubic yards), and under a 24 ft round pool 75.4 cu ft (2.79 cubic yards), before the sand cove at the wall. Follow your pool's manual for the depth and the cove.
How many bags of play sand do I need for a sandbox?
25 bags of 50 lb for a 5 x 5 ft sandbox filled 6 inches deep: 25 × 6 ÷ 12 = 12.5 cu ft, and each bag holds about 0.5 cu ft. A 4 x 4 ft box takes 16 bags at 6 inches and an 8 x 8 ft box 64. Sandbox maker KidKraft suggests 4 to 6 inches of sand in a box 8 inches deep, with a few inches left at the top.
How deep should sand be under a swing set?
The CPSC's Outdoor Home Playground Safety Handbook calls for at least 9 inches of sand for equipment up to 5 ft high, and a 12 inch initial fill compresses to about 9 inches. For taller equipment (up to 8 ft), it lists wood mulch, engineered wood fiber, or shredded rubber instead.
How much sand do I need for a horse arena?
About 6.2 cubic yards (8 to 9 tons of dry sand) for every 1,000 sq ft at 2 inches deep, the depth Penn State Extension suggests starting with. A 60 x 120 ft arena takes 44.4 cubic yards, or 57.8 to 64.4 tons, at 2 inches. Add sand 1/2 inch at a time as needed and stay under 6 inches, which Penn State says is stressful to horse tendons; University of Kentucky Extension puts the riding surface at 2 to 6 inches, depending on use.
Sources
- US Army FM 5-434 (MCRP 3-17.7I): Earthmoving Operations, Table 1-2 (PDF)
- NIST Handbook 44 (2026), Appendix C: General Tables of Units of Measurement (PDF)
- CMHA: Pavers on Aggregate Base, Guide Specification (PDF)
- U.S. Consumer Product Safety Commission: Outdoor Home Playground Safety Handbook (PDF)
- QUIKRETE: Mason Sand data sheet (PDF)
- QUIKRETE: Sand and Gravel Products data sheet (PDF)
- QUIKRETE: Premium Play Sand
- QUIKRETE 0.5 cu ft, 50 lb Play Sand (product listing)
- Sakrete 0.5 cu ft, 50 lb Play Sand (product listing)
- Sakrete Damp Mason Sand 50 lb (product listing)
- Above-ground oval pool owner's manual (Reprieve), hosted by INYO Pools (PDF)
- Royal Swimming Pools: How much sand do I need for my pool's base?
- Penn State Extension: Riding Arena Footing Material Selection and Management
- University of Kentucky Cooperative Extension: Riding Arena Footing: Materials and Characteristics (ID-265, PDF)
- University of Kentucky Cooperative Extension: Suitable Spaces for Indoor Horse Activities (ID-259, PDF)
- QUIKRETE: Jointing Sands (news release, PDF)
- KidKraft: How Much Sand for a Sandbox
Spot an error? Tell us.