Asphalt Calculator: How Many Tons of Asphalt Do I Need?

A 50 x 12 ft driveway paved 3 in thick (measured after rolling) takes about 11 tons of hot-mix asphalt: 66.67 sq yd × 3 in × 110 lb per sq yd per inch = 22,000 lb.

How much asphalt do you need?

Enter the area to pave, the asphalt thickness after rolling, and the mix weight from your supplier (a typical compacted mix weighs 108 to 120 lb per sq yd per inch). Add a gravel base depth to size the stone under it, or 0 for none.

ft
ft
in
lb
%
in

For estimating only: your paving contractor and local code set the thickness and base. Enter the thickness after rolling. 110 lb per sq yd per inch is about 147 lb per cu ft; ask your supplier for your mix. Base tons assume 1.4 tons per cu yd of crushed stone.

To figure asphalt by hand, turn the area into square yards (square feet ÷ 9), multiply by the compacted thickness in inches and by the mix weight, about 110 lb per square yard per inch, then divide by 2,000 for tons. Tennessee's DOT and Pennsylvania's asphalt pavement association figure tonnage the same way.

Our asphalt calculator also gives the compacted cubic yards and, if you enter a base depth, the crushed stone for the gravel base. It doesn't design the pavement: the thickness and the base come from your paving contractor and your local code.

How to measure for an asphalt driveway

  1. Measure the area to pave in feet (12 ft 6 in is 12.5 ft). Split the apron, flares, and any parking pad into rectangles; the square footage calculator adds up to three. If you know the total square feet, enter it as the length and 1 as the width.
  2. Enter the compacted thickness from your contractor's proposal. That's the thickness after rolling, not the loose layer the paver lays down.
  3. Enter the mix weight. 110 lb per sq yd per inch is within the typical range; your supplier's mix may differ (see below).
  4. Add the gravel base depth if new stone goes under the asphalt, or 0 if you're paving over an existing base or building full-depth asphalt.
  5. Leave Extra at 0 unless your contractor wants a margin.

The asphalt formula

  • Area (sq yd) = length (ft) × width (ft) ÷ 9
  • Asphalt (lb) = sq yd × compacted thickness (in) × mix weight (lb per sq yd per inch)
  • Tons = lb ÷ 2,000, plus any extra percentage
  • Cubic yards = length × width × thickness (in) ÷ 12 ÷ 27 (the cubic yard calculator does the same for circles and triangles)
  • Gravel base = length × width × base depth (in) ÷ 12 ÷ 27 cubic yards, × 1.4 for tons

The tons line is the one in a 2016 Tennessee DOT design bulletin: "Area (S.Y.) × Lb per SY per inch thickness / 2,000 Lb./ Ton = Tons". A square yard 1 inch thick is 0.75 cu ft, so 110 lb per sq yd per inch is 146.67 lb per cu ft (the Pennsylvania Asphalt Pavement Association's checklist rounds it: "110 lb/sy/in or 147 lbs/cf"), or 1.98 tons per cubic yard.

Worked example (the calculator's default values)

A 50 x 12 ft driveway (an example size), paved 3 in thick after rolling with mix at 110 lb per sq yd per inch, on a 6 in gravel base, one of the builds in the thickness table below:

  1. Area: 50 × 12 = 600 sq ft, ÷ 9 = 66.67 sq yd.
  2. Weight: 66.67 × 3 × 110 = 22,000 lb, ÷ 2,000 = 11 tons.
  3. Volume: 600 × 3 ÷ 12 = 150 cu ft, ÷ 27 = 5.56 cu yd.
  4. Base: 600 × 6 ÷ 12 = 300 cu ft, ÷ 27 = 11.11 cu yd, × 1.4 = 15.56 tons.

The calculator shows: "You need about 11 tons of asphalt (5.56 cu yd compacted)." and "Area: 600 sq ft (66.67 sq yd). At 3 in compacted and 110 lb per sq yd per inch (146.67 lb per cu ft): 66.67 x 3 x 110 = 22,000 lb, or 11 tons. Gravel base: 11.11 cu yd (about 15.56 tons) of crushed stone at 6 in deep."

Other builds on the same driveway

  • Full-depth asphalt, 4 in, no gravel base: about 14.67 tons (7.41 cu yd). At 6 in it's 22 tons.
  • Two courses, 2 in + 1.5 in = 3.5 in: about 12.83 tons, with the same 11.11 cu yd of base at 6 in.
  • A 1.5 in overlay of the old driveway: about 5.5 tons, no base.
  • The default with 5% extra: about 11.55 tons (5.83 cu yd).
Asphalt for a 50 by 12 foot driveway: about 11 tons at 3 inches compactedPlan of a driveway 50 feet long and 12 feet wide: 600 square feet, or 66.67 square yards. One square yard of asphalt 1 inch thick is 0.75 cubic feet and weighs about 110 pounds, which is 146.67 pounds per cubic foot. A cross-section shows 3 inches of compacted asphalt, laid about 3.75 inches thick before rolling, on a 6 inch compacted gravel base over the soil subgrade. The asphalt is 66.67 times 3 times 110, or 22,000 pounds, which is 11 tons, and 600 times 3 divided by 12 is 150 cubic feet, or 5.56 cubic yards. The gravel base is 300 cubic feet, or 11.11 cubic yards, about 15.56 tons at 1.4 tons per cubic yard. The section is drawn at a larger scale than the plan.ASPHALT FOR A 50 × 12 FT DRIVEWAY, 3 IN COMPACTED600 sq ft = 66.67 sq yd50 ft12 ft1 sq yd1 in thick= 0.75 cu ft ≈ 110 lb146.67 lb per cu ftSection (drawn larger than the plan)laid about 3.75 in, rolled to 3 inAsphalt · 3 in compactedGravel base · 6 incrushed stone, compactedSubgrade · compacted soilArea: 50 × 12 ft = 600 sq ft ÷ 9 = 66.67 sq ydAsphalt: 66.67 × 3 in × 110 lb = 22,000 lb ÷ 2,000 = 11 tonsVolume: 600 × 3 in ÷ 12 = 150 cu ft ÷ 27 = 5.56 cu ydBase, 6 in: 300 cu ft ÷ 27 = 11.11 cu yd × 1.4 = 15.56 tons
600 sq ft ÷ 9 = 66.67 sq yd. One square yard 1 in thick is 0.75 cu ft, about 110 lb of compacted mix, so 66.67 × 3 in × 110 lb = 22,000 lb, or 11 tons (5.56 cu yd). The 6 in gravel base is 11.11 cu yd, about 15.56 tons at 1.4 tons per cu yd. Rolled to 3 in, the mix goes down about 3.75 in thick.

Asphalt tons by driveway size and thickness

Tons of hot mix at 110 lb per sq yd per inch, compacted, with no extra and no base. The sizes are examples.

Driveway (ft)2 in3 in3.5 in4 in6 in
20 x 10 (200 sq ft)2.443.674.284.897.33
40 x 10 (400 sq ft)4.897.338.569.7814.67
50 x 12 (600 sq ft)7.331112.8314.6722
40 x 16 (640 sq ft)7.8211.7313.6915.6423.47
40 x 20 (800 sq ft)9.7814.6717.1119.5629.33
50 x 24 (1,200 sq ft)14.672225.6729.3344

Turned around, one ton covers about 81.82 sq ft at 2 in, 54.55 sq ft at 3 in, and 40.91 sq ft at 4 in.

Square feet per ton of asphalt, by thickness

One ton of hot mix covers about 54.55 sq ft at 3 in compacted. At 110 lb per sq yd per inch, each compacted inch weighs 12.22 lb per sq ft, so a ton covers 163.64 sq ft divided by the thickness in inches, and every 1,000 sq ft takes 6.11 tons per inch.

Thickness (compacted)Asphalt per sq ftOne ton coversTons per 1,000 sq ft
1 in12.22 lb163.64 sq ft (18.18 sq yd)6.11
1.5 in18.33 lb109.09 sq ft (12.12 sq yd)9.17
2 in24.44 lb81.82 sq ft (9.09 sq yd)12.22
2.5 in30.56 lb65.45 sq ft (7.27 sq yd)15.28
3 in36.67 lb54.55 sq ft (6.06 sq yd)18.33
3.5 in42.78 lb46.75 sq ft (5.19 sq yd)21.39
4 in48.89 lb40.91 sq ft (4.55 sq yd)24.44
5 in61.11 lb32.73 sq ft (3.64 sq yd)30.56
6 in73.33 lb27.27 sq ft (3.03 sq yd)36.67

The last column is the calculator's result for 1,000 sq ft entered as a length of 1,000 and a width of 1, with the base at 0. Many online asphalt calculators weigh the mix at 145 lb per cu ft instead. That is 108.75 lb per sq yd per inch, about 1 percent lighter, so a ton covers about 82.76 sq ft at 2 in, 55.17 sq ft at 3 in, and 41.38 sq ft at 4 in, and 1,000 sq ft at 2 in takes 12.08 tons. Both weights sit inside the Pennsylvania Asphalt Pavement Association's typical range of 144 to 160 lb per cu ft.

How thick should an asphalt driveway be?

Two state asphalt pavement associations give these driveway builds:

BuildAsphalt, compactedBase under itSource
Full-depth asphalt4 in may be adequate; 5 or 6 in is strongerNone: asphalt from the soil subgrade upIllinois Asphalt Pavement Association
Asphalt on aggregate3 in6 to 8 in of compacted aggregateIllinois Asphalt Pavement Association
Two courses on aggregate2 in bottom + 1.5 in surface (3.5 in)6 to 8 in of crushed aggregateColorado Asphalt Pavement Association
Overlay of an old driveway1.5 to 2 inThe existing pavementBoth

The Illinois page says 5 or 6 in "will assure you of a stronger, stable driveway under a wider range of climate and loads," and it quotes a vice president of the National Asphalt Pavement Association: "We recommend full-depth asphalt for driveways," adding that "1 inch of asphalt pavement is equivalent to 3 inches of aggregate base." By that ratio, 3 in of asphalt on 6 in of stone compares with about 5 in of full-depth asphalt.

These are guide figures, not a pavement design. Follow your local code and have a paving contractor set the thickness and base for your soil, drainage, and vehicles. A concrete driveway has its own minimums; the concrete calculator guide lists them.

Asphalt thickness for parking lots and heavier traffic

A parking lot carries more traffic than a home driveway, so it gets more asphalt. The Illinois Asphalt Pavement Association's parking lot page gives typical minimum designs for poor subgrade, which it calls typical in Illinois: asphalt layers on a 6 in aggregate layer, or full-depth asphalt placed on the soil subgrade.

Traffic (Illinois Asphalt Pavement Association)On 6 in of aggregateFull-depth asphaltTons of asphalt per 1,000 sq ft
Light duty: under 1,500 vehicles a day, mostly passenger vehicles, under 2% single unit trucks4 in: 2.5 in base layer + 1.5 in surface5 in24.44 on aggregate, 30.56 full-depth
Moderate duty: 700 to 3,000 vehicles a day, mostly passenger vehicles, under 5% single unit trucks and 3% combination trucks5.5 in: 2.5 in + 1.5 in base layers + 1.5 in surface6.5 in33.61 on aggregate, 39.72 full-depth
Heavy duty: 3,000 to 24,000 vehicles a day, the same truck shares6.5 in: two 2.5 in base layers + 1.5 in surface8 in39.72 on aggregate, 48.89 full-depth

The thicknesses are finished, compacted layers, and the association says each layer must be at least three times as thick as the largest aggregate in its mix. It warns that light-duty sections at entrances, exits, drive-throughs, truck loading docks, and trash dumpsters can fail early. The 6 in aggregate layer is 18.52 cu yd, about 25.93 tons at the calculator's 1.4 tons per cubic yard, for every 1,000 sq ft. A home driveway sits below the light-duty lot: 3 in on 6 to 8 in of aggregate, or 4 in of full-depth asphalt, in the builds table above. A lot's pavement design comes from an engineer or paving contractor.

How much does asphalt weigh?

It depends on the mix. The Pennsylvania Asphalt Pavement Association's checklist says: "A typical compacted asphalt mix will weigh 108 to 120 pounds per square yard per inch thickness (lbs/sy/in) or 144 to 160 pounds per cubic foot (lbs/cf)." Its examples use 110, and it advises checking your project's mix design. Tennessee DOT's bulletin assigns 106 to its Grading D surface mixes, 110 to 115 to most of its base mixes, and 88 to its OGFC surface mix.

lb per sq yd per inchlb per cu ftTons per cu ydExample driveway, 3 in
106141.331.90810.6 tons
1081441.94410.8 tons
110146.671.9811 tons
115153.332.0711.5 tons
1201602.1612 tons

If your supplier quotes pounds per cubic foot, multiply by 0.75 to get the calculator's unit: 145 lb per cu ft is 108.75 lb per sq yd per inch, or 10.88 tons for the example driveway. Typing 145 straight into the field would give 14.5 tons, about 32% too much.

Compacted thickness vs. laid thickness

Hot mix goes down loose and gets thinner under the rollers. The National Asphalt Pavement Association's paving handbook gives "a common rolldown factor (for a typical dense-graded mix) being approximately 25 percent," with a 2 in compacted lift laid 2.5 in thick. So a 3 in driveway starts near 3.75 in. Rolling packs the same tons into less depth, which is why the calculator pairs the compacted thickness with a compacted weight.

The Illinois association says asphalt is best placed in layers (lifts): "a total of 2 to 3 inches may be spread as two layers each 1-1/2 inches thick when compacted," and that a good way to pave a 4 in mat is to place 2.5 in, compact it, then pave and compact the rest. The total tons don't depend on the number of lifts. Thinner lifts need warmer weather: the same page wants air and surface temperatures above 70°F for a 1.5 in lift and above 40°F for a 2 in lift.

The gravel base under the asphalt

Both associations put 6 to 8 in of aggregate under an asphalt driveway that isn't full-depth, so the base field starts at 6. The Colorado guide adds that the subgrade should be graded smooth and free of organic material, with weak spots dug out and replaced, and the base compacted with rollers.

The calculator weighs the base at 1.4 tons per cubic yard, the same figure as our paver calculator. Select Sand & Gravel puts crushed stone at roughly 1.35 to 1.4 tons per yard, and crusher run or road base at up to 1.5. The base line is the finished, compacted volume. To order loose stone, run the depth through the gravel calculator, whose guide covers the compaction allowance, and use your supplier's weight. For a paver driveway instead, the paver calculator sizes the base, sand, and pavers.

Gravel base by driveway size

The gravel base for the driveway sizes in the tons table, at both ends of the 6 to 8 in of aggregate that the Illinois and Colorado associations give. These are the calculator's base line: compacted cubic yards, and tons at 1.4 tons per cubic yard.

Driveway (ft)Base at 6 inBase at 8 in
20 x 10 (200 sq ft)3.7 cu yd (5.19 tons)4.94 cu yd (6.91 tons)
40 x 10 (400 sq ft)7.41 cu yd (10.37 tons)9.88 cu yd (13.83 tons)
50 x 12 (600 sq ft)11.11 cu yd (15.56 tons)14.81 cu yd (20.74 tons)
40 x 16 (640 sq ft)11.85 cu yd (16.59 tons)15.8 cu yd (22.12 tons)
40 x 20 (800 sq ft)14.81 cu yd (20.74 tons)19.75 cu yd (27.65 tons)
50 x 24 (1,200 sq ft)22.22 cu yd (31.11 tons)29.63 cu yd (41.48 tons)

Each inch of base adds 3.09 cu yd, about 4.32 tons, per 1,000 sq ft. Full-depth asphalt goes on the soil subgrade with no gravel base, so enter 0 for it.

Tips and common mistakes

  • Entering the laid thickness. Use the compacted thickness from the proposal, or the tons come out about a quarter too high.
  • Measuring only the straight run. The apron and any parking pad count too.
  • Ignoring drainage. The Illinois association says to make sure your contractor "plans and builds adequate surface slopes to produce good drainage," and calls standing water on or near the driveway undesirable. The Colorado guide says drainage, crown, and slopes "need to be addressed."
  • Overlaying without repairs. For an overlay, the Illinois association says to have the contractor patch serious holes or cracks with asphalt and compact it first, or the trouble spots may reflect up through the new pavement.
  • Skipping upkeep. The Colorado guide says a high-grade asphalt liquid sealer applied every two to five years can extend the driveway's service life and improve its appearance.

Cold patch bags for potholes

Before an overlay, the Colorado guide says weak spots, holes, and large cracks should be cut out and patched with hot mix, and that small holes and cracks can be filled with driveway maintenance products. For a pothole, Quikrete's data sheets give the yield of its bagged patches: a 50 lb bag of Asphalt Cold Patch (No. 1701-58) makes about 0.5 cu ft when properly compacted, or about 6 sq ft at 1 in thick, and a 60 lb bag of Blacktop Patch (No. 1701-60) about 0.6 cu ft, or 7.2 sq ft at 1 in. Bags = length (ft) × width (ft) × depth (in) ÷ 12 ÷ the bag's yield, rounded up. The table counts 50 lb bags.

Pothole (ft)1 in deep2 in deep3 in deep
1 x 10.08 cu ft: 1 bag0.17 cu ft: 1 bag0.25 cu ft: 1 bag
1.5 x 1.50.19 cu ft: 1 bag0.38 cu ft: 1 bag0.56 cu ft: 2 bags
2 x 20.33 cu ft: 1 bag0.67 cu ft: 2 bags1 cu ft: 2 bags
2 x 30.5 cu ft: 1 bag1 cu ft: 2 bags1.5 cu ft: 3 bags
3 x 30.75 cu ft: 2 bags1.5 cu ft: 3 bags2.25 cu ft: 5 bags

With 60 lb bags of Blacktop Patch, divide by 0.6 instead: the counts are the same except 1 bag for the 1.5 x 1.5 ft hole and 4 bags for the 3 x 3 ft hole, both at 3 in. Quikrete says to square-cut the sides, remove loose material, and sweep; to place the patch 1 to 3 in deep in 1 in lifts, compacting each one; to fill the last lift about 1/2 in above the surrounding surface and tamp it level; and to keep a repair to about 3 x 3 ft. Traffic can use it as soon as it is leveled and compacted. The calculator can do the math too: both patches weigh 100 lb per cu ft compacted, so enter 75 as the mix weight (100 × 0.75), the hole's size and depth, and 0 for the base, then divide the pounds in the result by the bag weight. A 3 x 3 ft hole 2 in deep shows 150 lb, or 3 bags of 50 lb.

Frequently asked questions

How many tons of asphalt do I need for a driveway?

About 11 tons for a 50 x 12 ft driveway at 3 in compacted, and 14.67 tons at 4 in. Multiply the square yards by the compacted inches and by about 110 lb, then divide by 2,000.

How much asphalt do I need?

About 1.83 tons per 100 sq ft at 3 in compacted, 1.22 tons at 2 in, and 2.44 tons at 4 in: square yards × compacted inches × about 110 lb, ÷ 2,000. For a 50 x 12 ft driveway, the Illinois Asphalt Pavement Association's two builds come to 11 tons for 3 in over 6 to 8 in of aggregate (11.11 to 14.81 cu yd of base), or 14.67 tons for 4 in of full-depth asphalt.

How much asphalt do I need for 1,000 square feet?

About 18.33 tons at 3 in compacted: 1,000 sq ft is 111.11 sq yd, and 111.11 × 3 × 110 lb = 36,667 lb. At 2 in it takes 12.22 tons, and at 4 in 24.44 tons, at 110 lb per sq yd per inch. That is about 36.67 lb of asphalt per sq ft at 3 in.

How much area does a ton of asphalt cover?

About 81.82 sq ft at 2 in, 54.55 sq ft at 3 in, and 40.91 sq ft at 4 in, at 110 lb per sq yd per inch (9.09, 6.06, and 4.55 sq yd). At 145 lb per cu ft, the weight many online calculators use, a ton covers about 82.76, 55.17, and 41.38 sq ft.

How much does asphalt weigh per cubic foot?

144 to 160 lb per cu ft (108 to 120 lb per sq yd per inch) for typical compacted mix, says the Pennsylvania Asphalt Pavement Association, which uses 147 lb per cu ft (110 lb per sq yd per inch) in its examples.

How many cubic yards are in a ton of asphalt?

About 0.505 cu yd, or 13.64 cu ft: at 110 lb per sq yd per inch, compacted asphalt weighs 1.98 tons per cubic yard.

How much does a yard of asphalt weigh?

About 1.98 tons (3,960 lb) per compacted cubic yard at 110 lb per sq yd per inch, which is 146.67 lb per cu ft. The Pennsylvania Asphalt Pavement Association's typical range of 144 to 160 lb per cu ft gives 1.94 to 2.16 tons per cubic yard, and 145 lb per cu ft gives about 1.96 tons (3,915 lb).

How thick should an asphalt driveway be?

4 in of full-depth asphalt may be adequate and 5 or 6 in is stronger, says the Illinois Asphalt Pavement Association, or 3 in over 6 to 8 in of compacted aggregate. The Colorado association's build is a 2 in bottom course and a 1.5 in surface course over 6 to 8 in of crushed aggregate. Follow your local code and your paving contractor.

How thick should asphalt be for a parking lot?

4 in of asphalt on 6 in of aggregate, or 5 in of full-depth asphalt, for a light-duty lot (under 1,500 vehicles a day, mostly passenger vehicles), in the Illinois Asphalt Pavement Association's typical minimum designs for poor subgrade. Moderate duty takes 5.5 in on 6 in of aggregate or 6.5 in full-depth, and heavy duty 6.5 in or 8 in. At 110 lb per sq yd per inch, 4 in is 24.44 tons per 1,000 sq ft.

How much gravel do I need under an asphalt driveway?

6 to 8 in of compacted aggregate under 3 in of asphalt, per the Illinois association (the Colorado guide gives 6 to 8 in of crushed aggregate): 11.11 cu yd, about 15.56 tons, for a 50 x 12 ft driveway at 6 in, or 14.81 cu yd (20.74 tons) at 8 in. These are compacted volumes at 1.4 tons per cubic yard. Full-depth asphalt needs no gravel base.

How thick is asphalt before it's rolled?

About 25 percent thicker for a typical dense-graded mix, per the National Asphalt Pavement Association's handbook: a 2 in compacted lift is laid 2.5 in thick, so 3 in compacted starts near 3.75 in.

How many bags of cold patch do I need?

2 bags of 50 lb for a 2 x 2 ft pothole 2 in deep. Quikrete's Asphalt Cold Patch yields about 0.5 cu ft per 50 lb bag when compacted, about 6 sq ft at 1 in thick, so divide the hole's volume (length × width in feet × depth in inches ÷ 12) by 0.5 and round up: a 3 x 3 ft hole 3 in deep is 2.25 cu ft, or 5 bags. Its 60 lb Blacktop Patch yields about 0.6 cu ft, 4 bags for that hole.

Spot an error? Tell us.